Schneider Electric Xantrex XW Guia de Instalação Página 55
- Página / 166
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
Step 4: Wiring the Inverter
975-0239-01-01 2–25
This manual for use by qualified personnel only
AC Wiring to the Xantrex XW Power Distribution Panel
To connect the Xantrex XW Power Distribution Panel to the inverter:
1. Connect the neutral wire first to the N-LOAD terminal. Connect the wires
labelled “INV1 N-LOAD (SPLIT PHASE)”, “INV1 L1-LOAD, and “INV1
L2-LOAD” (from the L1 and L2 terminals on the input (top) side of the output
breaker and the neutral bus) to the AC Load (L1-LOAD, N-LOAD, L2-LOAD)
terminals on the inverter.
2. Connect the wires labelled “INV1 L1-GRID” and “INV1 L2-GRID” to the
inverter. If the AC source will be the utility grid, connect to the GRID (AC1)
terminals (L1-GRID, L2-GRID). If the system will be off-grid and the only AC
source will be a generator, these wires can be connected to the GEN (AC2)
terminals (L1-GEN, L2-GEN). No additional neutral connection is needed
when using the Xantrex XW Power Distribution Panel. (Additional neutral
terminals (N-GRID, N-GEN) are provided on the inverter for installations that
do not use the Xantrex XW Power Distribution Panel.)
3. Connect L1 (from the L1 output Power Distribution Bar) and L2 (from the L2
output Power Distribution Bar), Neutral, and Ground to the sub-panel that
supplies power to inverter loads.
4. Connect the ground wire between the Xantrex XW Power Distribution Panel
and the utility grid AC panel. Connect Neutral from the Xantrex XW Power
Distribution Panel to the utility grid AC panel. Connect L1 and L2 from the
input side of the AC1 Breaker (L1 and L2 Power Distribution bars) to the utility
grid AC Panel.
Important: The Xantrex XW Inverter/Charger is provided with fixed disconnect
limits for voltage and frequency. These limits are fixed when the unit is exporting
power to the grid. The unit shall not be aggregated such that it can export more
than 30 kW on a single point of common connection.
Important: Both lines of input power must be connected in order for the Xantrex
XW Inverter/Charger to operate. For example, L1 and L2 of Grid Input and/or L1
and L2 of Gen Input need to be connected.
- Xantrex™ XW Power System 1
- Xantrex XW Power System 3
- Copyright and Contact 4
- About This Guide 5
- Conventions Used 6
- Related Information 6
- Important Safety Instructions 7
- Limitations on Use 8
- Single-phase Operation Only 8
- Explosive Gas Precautions 8
- FCC Information to the User 9
- Contents 11
- A Specifications 14
- B Wiring Diagrams 14
- 1 Introduction 21
- System Overview 22
- Xantrex XW Conduit Box 24
- 975-0239-01-01 1–5 25
- FGA Number: 28
- 865-1050 28
- 865-1060 29
- 2 Inverter/Charger 31
- Pre-Installation 32
- Clearance Requirements 34
- Mounting 34
- Inverter/Charger Installation 36
- 2–6 975-0239-01-01 36
- Step 2: Mounting the Inverter 37
- Step 4: Wiring the Inverter 39
- Inverter Grounding 44
- Grounding the DC System 45
- 975-0239-01-01 2–17 47
- Making DC Connections 48
- Making AC Connections 50
- CAUTION: 51
- Damage to the Inverter 51
- Grounding the AC System 53
- 2–26 975-0239-01-01 56
- 975-0239-01-01 2–27 57
- Distribution Panel 58
- AUX Port 60
- User Line Wiring 61
- AUX Port Terminal Assignments 61
- Confirm All Connections 62
- Enable the Inverter 63
- AC Voltage Check 64
- 2–36 975-0239-01-01 66
- Installation Steps 67
- Power Distribution Panel 68
- 975-0239-01-01 2–39 69
- 975-0239-01-01 2–41 71
- 2–42 975-0239-01-01 72
- See Figure 2-9 on page 2–14 76
- 975-0239-01-01 2–47 77
- 2–48 975-0239-01-01 78
- 2–52 975-0239-01-01 82
- 975-0239-01-01 2–53 83
- 3 Xantrex Xanbus 85
- The Xantrex Xanbus System 86
- Network Components 87
- Ordering Network Components 88
- Network Layout 89
- Installing the Network 90
- 4 Xantrex XW Solar 93
- PV Array Requirements 94
- Remove screws to access 97
- Removing Knockouts 98
- Mounting the Controller 99
- Secure with two more screws 100
- Place keyhole slot 100
- ¼" 6 mm 100
- Grounding 101
- WARNING: Shock Hazard 102
- WARNING: Fire Hazard 102
- Ungrounded Arrays 103
- Minimum Wire Gauge 105
- Over-current Protection 105
- Current Rating 105
- WARNING: Equipment damage 106
- Commissioning 111
- 5 Xantrex XW System 115
- Materials and Tools Required 117
- Choosing a Location 117
- WARNING: Explosion hazard 117
- WARNING: Shock hazard 118
- Rotate tabs to 119
- CAUTION: Equipment damage 120
- Verifying the Installation 122
- Preparing an Installation 123
- WARNING: Explosion Hazard 124
- CAUTION: Shock Hazard 126
- N/OFF/LED Indicator 128
- N/OFF/LED Indicator return 128
- Connecting the Generator 129
- CAUTION: Equipment Damage 131
- N/OFF switch. This light 132
- Verifying Power Is Available 135
- A Specifications 137
- Electrical Specifications 138
- Connection 139
- Specifications 140
- A–4 975-0239-01-01 140
- Ambient Temperature (°C) 141
- Xantrex XW Series Efficiency 142
- Charging Power Factor 143
- Mechanical Specifications 144
- Accessories 145
- B Wiring Diagrams 147
- 975-0239-01-01 B–3 149
- Xantrex Xanbus 150
- Network Terminator 150
- Xantrex XW Inverter/Charger 150
- Wiring Diagrams 152
- B–6 975-0239-01-01 152
- 975-0239-01-01 B–7 153
- B–8 975-0239-01-01 154
- C Alternate System 155
- 975-0239-01-01 C–3 157
- C–4 975-0239-01-01 158
- 975-0239-01-01 C–5 159
- CAUTION: Damage to Equipment 161
- Schneider Electric 166
Manuais e produtos relacionados com Sistemas de segurança - controlo de acesso Schneider Electric Xantrex XW
(58 páginas)© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.068 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais