Schneider Electric Xantrex XW Guia de Instalação Página 131
- Página / 166
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
The Xantrex XW Automatic Generator Start
975-0239-01-01 5–17
This manual for use by qualified personnel only
Connecting an External Manual ON/OFF Switch (Optional)
The external manual ON/OFF inputs (wires 7 and 8 on the wiring harness) are
intended for wiring to one or more remote O
N/OFF switches for starting and
stopping the generator manually. The other contact of the switch should be
connected to ground. In order for the Xantrex XW Automatic Generator Start to
be able to detect these switches, wire the positive of the generator battery to the
constant 12-volt/24-volt generator battery positive (wire 10 on the Xantrex XW
Automatic Generator Start wiring harness). See Figure 5-7.
If the generator battery does not have the required voltage, any 12-volt or 24-volt
power source will suit this purpose. If an alternate power source is used, the
negative of the power source must be connect to the other contact of the switch.
Multiple control panels or simple contact closures can be wired to the external
manual O
N/OFF inputs. The Xantrex XW Automatic Generator Start detects if any
of the contacts close and will change its operating mode to External Manual On
or External Manual Off (for more information, see the Xantrex XW Automatic
Generator Start Owner’s Guide). The Xantrex XW Automatic Generator Start turns
the generator on or off according to these inputs and the resulting operating
mode change.
The External Manual On and External Manual Off states are not affected by
maximum generator run time. See the Xantrex XW Automatic Generator Start
Owner’s Guide for additional information.
CAUTION: Equipment Damage
Do not connect the Xantrex XW Automatic Generator Start to a 48-volt battery
bank. The Xantrex XW Automatic Generator Start is limited to a 30V open-circuit
maximum by its regulatory approval and cannot be connected to a 48-volt power
source. Furthermore, tapping 12-volts or 24-volts from a 48-volt battery bank will
unevenly wear out the batteries and shortens the battery bank life.
Table 5-6 Wiring for Connecting an External Manual ON/OFF Switch
Wire Number Function
Wiring Harness
Wire Color
7 External manual on input White/Green
8 External manual off input White/Red
9 External O
N/OFF LED Indicator output White/Blue
10 Constant 12/24 V B+ for
External O
N/OFF/LED Indicator
Red
11 External O
N/OFF/LED Indicator return Black
- Xantrex™ XW Power System 1
- Xantrex XW Power System 3
- Copyright and Contact 4
- About This Guide 5
- Conventions Used 6
- Related Information 6
- Important Safety Instructions 7
- Limitations on Use 8
- Single-phase Operation Only 8
- Explosive Gas Precautions 8
- FCC Information to the User 9
- Contents 11
- A Specifications 14
- B Wiring Diagrams 14
- 1 Introduction 21
- System Overview 22
- Xantrex XW Conduit Box 24
- 975-0239-01-01 1–5 25
- FGA Number: 28
- 865-1050 28
- 865-1060 29
- 2 Inverter/Charger 31
- Pre-Installation 32
- Clearance Requirements 34
- Mounting 34
- Inverter/Charger Installation 36
- 2–6 975-0239-01-01 36
- Step 2: Mounting the Inverter 37
- Step 4: Wiring the Inverter 39
- Inverter Grounding 44
- Grounding the DC System 45
- 975-0239-01-01 2–17 47
- Making DC Connections 48
- Making AC Connections 50
- CAUTION: 51
- Damage to the Inverter 51
- Grounding the AC System 53
- 2–26 975-0239-01-01 56
- 975-0239-01-01 2–27 57
- Distribution Panel 58
- AUX Port 60
- User Line Wiring 61
- AUX Port Terminal Assignments 61
- Confirm All Connections 62
- Enable the Inverter 63
- AC Voltage Check 64
- 2–36 975-0239-01-01 66
- Installation Steps 67
- Power Distribution Panel 68
- 975-0239-01-01 2–39 69
- 975-0239-01-01 2–41 71
- 2–42 975-0239-01-01 72
- See Figure 2-9 on page 2–14 76
- 975-0239-01-01 2–47 77
- 2–48 975-0239-01-01 78
- 2–52 975-0239-01-01 82
- 975-0239-01-01 2–53 83
- 3 Xantrex Xanbus 85
- The Xantrex Xanbus System 86
- Network Components 87
- Ordering Network Components 88
- Network Layout 89
- Installing the Network 90
- 4 Xantrex XW Solar 93
- PV Array Requirements 94
- Remove screws to access 97
- Removing Knockouts 98
- Mounting the Controller 99
- Secure with two more screws 100
- Place keyhole slot 100
- ¼" 6 mm 100
- Grounding 101
- WARNING: Shock Hazard 102
- WARNING: Fire Hazard 102
- Ungrounded Arrays 103
- Minimum Wire Gauge 105
- Over-current Protection 105
- Current Rating 105
- WARNING: Equipment damage 106
- Commissioning 111
- 5 Xantrex XW System 115
- Materials and Tools Required 117
- Choosing a Location 117
- WARNING: Explosion hazard 117
- WARNING: Shock hazard 118
- Rotate tabs to 119
- CAUTION: Equipment damage 120
- Verifying the Installation 122
- Preparing an Installation 123
- WARNING: Explosion Hazard 124
- CAUTION: Shock Hazard 126
- N/OFF/LED Indicator 128
- N/OFF/LED Indicator return 128
- Connecting the Generator 129
- CAUTION: Equipment Damage 131
- N/OFF switch. This light 132
- Verifying Power Is Available 135
- A Specifications 137
- Electrical Specifications 138
- Connection 139
- Specifications 140
- A–4 975-0239-01-01 140
- Ambient Temperature (°C) 141
- Xantrex XW Series Efficiency 142
- Charging Power Factor 143
- Mechanical Specifications 144
- Accessories 145
- B Wiring Diagrams 147
- 975-0239-01-01 B–3 149
- Xantrex Xanbus 150
- Network Terminator 150
- Xantrex XW Inverter/Charger 150
- Wiring Diagrams 152
- B–6 975-0239-01-01 152
- 975-0239-01-01 B–7 153
- B–8 975-0239-01-01 154
- C Alternate System 155
- 975-0239-01-01 C–3 157
- C–4 975-0239-01-01 158
- 975-0239-01-01 C–5 159
- CAUTION: Damage to Equipment 161
- Schneider Electric 166
Manuais e produtos relacionados com Sistemas de segurança - controlo de acesso Schneider Electric Xantrex XW
(58 páginas)© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.183 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais